NACE-CIP1-001 Exam Practice Questions prepared by NACE Professionals
Use Valid New NACE-CIP1-001 Questions - Top choice Help You Gain Success
NACE-CIP1-001 exam is an essential certification for individuals who wish to pursue a career in coating inspection. Coating Inspector Level 1 certification is recognized globally and is highly valued by employers in the corrosion prevention and control industry. Coating Inspector Level 1 certification provides a testament to the candidate's expertise in coating inspection and is often a prerequisite for higher levels of certification in the field. Candidates who wish to take the exam must meet certain eligibility requirements and complete a training course that covers the topics tested in the exam.
NEW QUESTION # 23
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Break the blisters to see what's inside
- B. Extract any liquid that may be inside the blister and send it to the lab for further analysis
- C. Document the problem and advise the Contractor and Owner's representative
- D. Document the problem and advise the Contractor
Answer: C
NEW QUESTION # 24
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Use another method as the comparator method is too subjective
- B. Record the segment with the less aggressive profile
- C. Record your result by identifying two segments
- D. Record the segment with the more aggressive profile
Answer: B
NEW QUESTION # 25
If a Thermoset coating is heated it will:
- A. Soften when heated and retain its softness when cooled
- B. Soften when heated and return to its original hardness when cooled
- C. Harden and retain its hardness when cooled
- D. Harden and return to its original hardness when cooled
Answer: C
NEW QUESTION # 26
Galvanic corrosion occurs on which of the following substrates:
- A. Concrete
- B. Metal
- C. Wood
- D. Fiberglass Reinforced Plastic
Answer: B
NEW QUESTION # 27
A magnetic pull-off type gauge is a good choice when:
- A. Accuracy is not required
- B. When working on non-ferrous metals
- C. Performing an adhesion test
- D. When an intrinsically safe tool is required
Answer: D
NEW QUESTION # 28
Dew point is the temperature at which
- A. condensation occurs.
- B. the air is saturated.
- C. humidity decreases
- D. water freezes.
Answer: A
NEW QUESTION # 29
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Atmospheric Corrosion
- B. Localized Corrosion
- C. General Corrosion
- D. Galvanic Corrosion
Answer: D
NEW QUESTION # 30
Stripe coats are generally applied to:
- A. Complex geometric shapes
- B. Edges and corners
- C. a), b), and c)
- D. Welds
Answer: C
NEW QUESTION # 31
Safety Data Sheets must be carefully reviewed by:
- A. The Inspection personnel
- B. The Owner's personnel
- C. The Application personnel
- D. All personnel involved in the job
Answer: D
NEW QUESTION # 32
Silicone coatings are typically:
- A. Applied in very thick films
- B. Used as a sacrificial primer
- C. Used strictly in immersion service
- D. Applied in very' thin films
Answer: D
NEW QUESTION # 33
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. High Relative Humidity
- B. Low Surface Temperature
- C. High Surface Temperature
- D. Low Relative Humidity
Answer: D
NEW QUESTION # 34
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Surface Condition H
- B. Rust Grades 1-4
- C. Surface Conditions E-G
- D. Rust Grades A-D
Answer: D
NEW QUESTION # 35
The main responsibilities of the inspector are to
- A. direct and perform the work stated in the specification.
- B. demonstrate to the contractor how to apply the coating.
- C. observe and report the quality of the work performed.
- D. observe and direct the work of the contractors.
Answer: C
NEW QUESTION # 36
Corrosion generally occurs at which of the following sites:
- A. Metallic pathway
- B. Electrolyte
- C. Cathode
- D. Anode
Answer: D
NEW QUESTION # 37
What is used to determine compressed air cleanliness?
- A. Blotter test
- B. Profilometer
- C. Needle pressure gauge
- D. Psychrometer
Answer: B
NEW QUESTION # 38
The initial steel condition is important to the NACE Inspector because:
- A. Less abrasive is need if the mill Scale s gone
- B. If the steel is pitted more coating will be required
- C. It affects the final appearance after blasting
- D. The Inspector may have to reject the Steel
Answer: D
NEW QUESTION # 39
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?
- A. 5 to 6 mils (125 to 150 microns)
- B. 8 to 10 mils (200 to 250 microns)
- C. 10 to 12 mils (250 to 300 microns)
- D. 6 to 7 mils (150 to 175 microns)
Answer: D
NEW QUESTION # 40
......
NACE-CIP1-001 Exam Practice Materials Collection: https://prep4sure.examtorrent.com/NACE-CIP1-001-exam-papers.html
